Enter the administrative password to be assigned to this controller. Note There is no default administrative password, you must enter a password. Enter the IP address of the management interface netmask.
The VLAN identifier should be set to match the switch interface configuration. Enter the port number of the access point manager interface. Ports values are 1 to 4. Enter the IP address of the controller virtual interface.
You should enter a fictitious, unassigned IP address, such as The virtual interface is used to support mobility management, DHCP relay, and embedded Layer 3 security such as guest web authentication and VPN termination. All controllers within a mobility group must be configured with the same virtual interface IP address. Although the name that you enter here is assigned to both the mobility group and the RF group, these groups are not identical. Both groups define clusters of controllers, but they have different purposes.
All of the controllers in an RF group are usually also in the same mobility group and vice versa. However, a mobility group facilitates scalable, system-wide mobility and controller redundancy while an RF group facilitates scalable, system-wide dynamic RF management. Enter the network name, or service set identifier SSID. This is the default SSID that the access points use when they join a controller. Values are yes or no. The following message appears:.
Values are YES or no. The default setting is YES. If you select YES, you are prompted to enter the following:. Enter the two letter country code. The default country code is the United States US. Choose YES to enable or no to disable the The default is YES.
Choose YES to enable or no disable the Choose YES to enable or no to disable radio resource management. The values are YES or no. The default value is YES. Enter a polling interval between and secs. Enter the polling interval between and seconds. Enter yes if the configuration entered is correct. Values are yes and no. If yes is entered. To log into the controller, follow these steps:. Step 1 Enter a valid username and password to log into the controller CLI.
Note The administrative username and password you created in the startup wizard are case sensitive. Step 2 The CLI displays the root level system prompt:. The system prompt can be any alphanumeric string up to 31 characters.
You can change it by entering the config prompt command. Make sure you enter the new prompt using double quotation marks. Note The CLI automatically logs out without saving any changes after 5 minutes of inactivity. You can set the automatic logout from 0 never log out to minutes using the config serial timeout command. Figure 13 shows the connection from the network Always use Category-5, Category-5e, Category-6, or Category-7 Ethernet cables to connect the office network equipment to the controller.
Note If the link does not activate, check the cable. When you are connecting to a hub or a switch, use a straight-through cable. After you have configured the controller, use Category-5, Category-5e, Category-6, or Category-7 Ethernet cables to connect up to 50 Cisco lightweight access points to the controller Ethernet ports or to the network distribution system as shown in Figure As soon as the controller is operational, the controller is available to connect access that are scanning for a controller.
When it detects an access point, it records the access point MAC address in its database. The controller Radio Resource Management RRM feature automatically configures the access point to start transmitting and allowing clients to associate.
Note With Release 7. Directly connected APs were not supported before Release 7. You have prepared the controller for basic operation. Refer to the Cisco Wireless Controller Configuration Guide for information on configuring the controller to meet the specific needs of your wireless network. Figure 14 Access Points Connected to a Controller. If your controller is not working properly, check the LEDs on the front panel of the unit.
You can use the LED indications to quickly assess the status of the unit. See Table 1 for a description of the front panel LEDs. The installation is complete. Refer to the Cisco Wireless Controller Configuration Guide for more information about configuring your controller. The guide is available on cisco. The Reset button on the front panel of the controller becomes active after the controller boots.
To reset the controller using the Reset button, follow these steps:. Step 1 Connect a PC to the controller console point. Step 2 Press and hold the Reset button for at least 3 seconds using a pointed object, such as a ball point pen, pencil, or paper clip. Step 3 After the controller reboots, enter your username and password at the prompts. If you have configured the controller, it reboots and loads the configuration. If you have not configured the controller, the configuration wizard appears.
This warning symbol means danger. Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen.
Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. Tilanne voi aiheuttaa ruumiillisia vammoja. Ce symbole d'avertissement indique un danger. Dieses Warnsymbol bedeutet Gefahr. Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. Dette advarselssymbolet betyr fare. Denna varningssignal signalerar fara.
Du befinner dig i en situation som kan leda till personskada. Er is ontploffingsgevaar als de batterij verkeerd vervangen wordt.
Vervang de batterij slechts met hetzelfde of een equivalent type dat door de fabrikant aanbevolen is. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften weggeworpen te worden. Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers. Sostituire solo con una di tipo uguale o equivalente, consigliata dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore. Skift kun med samme eller tilsvarende type som er anbefalt av produsenten. Kasser brukte batterier i henhold til produsentens instruksjoner.
Substitua a bateria por uma bateria igual ou de um tipo equivalente recomendado pelo fabricante. Explosionsfara vid felaktigt batteribyte. Deze apparatuur dient geaard te zijn. Neem contact op met de bevoegde instantie voor elektrische inspecties of met een elektricien als u er niet zeker van bent dat er voor passende aarding gezorgd is. Laitteiden on oltava maadoitettuja. Questa apparecchiatura deve essere dotata di messa a terra. Este equipamento deve ser aterrado.
Nunca anule o fio terra nem opere o equipamento sem um aterramento adequadamente instalado. Este equipo debe estar conectado a tierra. No inhabilite el conductor de tierra ni haga funcionar el equipo si no hay un conductor de tierra instalado correctamente.
Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen. Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.
Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais. Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. A listing of Cisco's trademarks can be found at www. Third party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between Cisco and any other company. Skip to content Skip to search Skip to footer. Available Languages. Download Options. Updated: December 6, About This Guide This guide is designed to help y Try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Safety Information Safety warnings appear throughout this guide in procedures that may harm you if performed incorrectly. When multiple controllers are mounted in an equipment rack, be sure that the power source is sufficiently rated to safely run all the equipment in the rack input: to VAC, 50—60 Hz, output: 80 W per controller.
Verify the integrity of the electrical ground before installing the controller. Doing so will damage the controller. Ports and Slots. Unpacking and Preparing the Controller for Operation Follow these steps to unpack the controller and prepare it for operation: Step 1 Open the shipping container and carefully remove the contents.
One Power supply and power cord power cord option configurable. Cisco Wireless Controller software pre-loaded on the controller software option configurable. Optional licenses will be pre-installed on controller at factory, if selected. Two Number 6 Phillips pan-head screws for mounting the controller on a desk, shelf, or wall. Two wall anchors. Strain relief clip and screw. They are easy to deploy, manage, and troubleshoot. Cisco show your logo We only include the brand logos of Open Icecat participants sponsors with whom we entered into a formal agreement to make their product content available for all their channel partners on their cisvo.
The Aironet fulfill the Simplify day-to-day IT management. Are fixed configuration, stackable Ethernet Gigabit switches that provide access Enterprise class for campus and Branch Office applications.
Please, try again later. Switches Get secure and reliable switches for any application, in any environment. The Network Convergence System Series is designed to clsco scale large enterprise, over-the-top OTTand service provider data center networking architectures. Shanghai Dongwen Industry Co. Product name is a key part of the Icecat product title on a product data-sheet. Cisco Catalyst Datasheeet switches enable high-performance enterprise networks, in addition to providing highly scalable, mobile, and secure user experiences.
More Sharing Services Share. Designed for networks of all sizes, Mobility Express offers industry-leading wireless LAN technology for its employees and customers. Please reply me within 24 hours. But the data-sheet is not yet standardized by an Icecat editor. Build a fast, datassheet network with these entry-level, low-cost, reliable networking solutions that provide plug-and-play connectivity. The ASR Series is designed to grow with your network and business need as a modular, high density, power efficient, and secure platform with software virtualization capabilities.
It is part of the Cisco digital network architecture and is optimized for the new generation of wireless networks, Catalyst CX and CX. One product can have multiple barcodes depending on logistic variations such as packaging or country.
The APes Series are highly secure and without the need of a wireless controller. Get the right performance for your organization with Cisco Small Business Series wireless access points thanks to its ease of deployment, affordable models and elegant designs. The SGX models provide 24 or 48 ports with Gigabit Ethernet connectivity with uplinks and at affordable prices. Your message has been sent to the following suppliers. This was increased to as of Release 7.
This was increased to 1Gbps as of Release 7. In Release 7. Note : The supports neither the wired guest feature before Version 8. Note : For an accurate list of supported features, check the release notes for your specific software release, which contain a Features not supported on WLC paragraph. These sections provide a greater insight into the architecture of the Cisco Series Wireless Controller.
The Cisco Series Wireless Controller physically has the same form factor as the Cisco controller. The CPU can handle control plane application, which handles all the management traffic needed to "control" a wireless network. Two types of memory devices are supported in order to store software images. The boot flash contains the boot code, and the compact flash contains the application code that can store multiple images. The front panel houses four Gigabit Ethernet ports. Two of the ports are Local TFTP server required in order to download the operating system software updates.
Cisco uses an integral TFTP server. If the controller is brought up for the first time with no prior configuration, it automatically enters into a wizard which asks you a series of configuration information. The wizard first will first prompt for user ID and password. This wizard cannot be bypassed and you must enter all the information it asks.
Caution : Do not connect a PoE cable to the console port. This action damages the controller. Complete these steps in order to connect the PC to the controller's console port:. Plug the RJ connector on a null-modem serial cable into the controller's console port and the other end of the cable into the PC's serial port.
Each port is, by default, an The VLAN trunking characteristics of the port are not configurable. An interface is a logical entity on the controller. Since LAG is not used, each interface is mapped to at least one primary physical port and an optional secondary port.
Multiple interfaces can be mapped to a single Wireless Controller port. There are multiple types of interfaces on the Wireless Controller, four of which are static types that must be present and are configured at setup time:. The management interface is the default interface for in-band management of the controller and connectivity to enterprise services such as Authentication, Authorization, and Accounting AAA servers.
The management interface is also used for communications between the controller and APs. The management interface is the only consistently "pingable" in-band interface IP address on the controller. The management interface acts like an AP manager interface by default. The dynamic interfaces for AP manager must have a unique IP address. Typically, this is configured on the same subnet as the management interface, but this is not necessarily a requirement. However, as a best practice, it is suggested to have 4 separate dynamic AP manager interfaces and associate them to the 4 Gigabit interfaces.
By default, the management interface acts like an AP-manager interface as well and it is associated to one Gigabit interface. As a result, if you use the management interface, you need to create only 3 more dynamic AP manager interfaces and associate them to the remaining 3 Gigabit interfaces. The virtual interface is used to support mobility management, DHCP relay, and embedded Layer 3 security like guest web authentication and VPN termination.
The virtual interface must be configured with an unassigned and unused gateway IP address. A typical virtual interface is 1.
The virtual interface address is not pingable and should not exist in any routing table in your network. The Cisco Series Wireless Controller will support up to 16 dynamic interfaces. There can be up to 16 WLANs configured per controller. Management servers, such as a radius server and NTP server, should not be in a dynamic interface subnet but should be either in the management interface subnet or any other subnet not added to the WLC.
By default, all four ports on the Cisco Series Wireless Controller are The controller is always connected to a Gigabit Ethernet port on the neighboring switch.
The neighbor switch port is configured as an All other VLANs are pruned. This is not necessary, but is a deployment best practice because when irrelevant VLANs are pruned, the controller only processes relevant frames which optimizes performance. This wizard output is taken from Release 7. Note : The previous configuration is an example.
It might differ from one install to another. The Cisco Series Wireless Controller does not have any licenses installed. Without any installed licenses, the APs will not be able to join the controller.
It is recommended to install appropriate licenses on the Cisco Series Wireless Controller in order to work with the controller as you go forward. The Cisco Series Wireless Controller is shipped with an evaluation license for a period of 60 days that is, 8 weeks 4 days. The evaluation license is a base license only. In both cases, there should be a TFTP server that hosts the license files. It provides advanced management tools like wireless coverage display and location-based services.
See the wireless software compatibility matrix as well as the Prime Infrastructure and WLC release notes for supported compatible releases. Prime Infrastructure uses SNMP in order to manage wireless controllers, access points, and client devices. Add new communities or modify as necessary. For simplicity, the defaults are used. Select Add device from the menu bar. Click OK. In order to verify the Cisco Series Wireless Controller after it is added in PI, go check back in the device work center if it is successfully synced and managed.
Wrong SNMP credentials might leave it "unmanaged".
0コメント